SKYDAS standart 3 RC 4
Burglar resistant security door SKYDAS STANDART 3 RC4 is designed to protect against experienced burglar that uses heavy duty tools.
-Burglar resistance tested and approved in Lithuania, KTU laboratory – RC4 (resistance class 4) by EN 1627:2011 standard; outswing doors only;
-At least one of the locks must be not lower than 5th security class, additionally protected by drilling resistant plate;
-Good soundproofing (41 dB Rw (C;Ctr)) and thermal transmittance (1,3 W/(m2K);
-May be fire resistant (EI30, EI45) and smoke resistant (SM C5);
-Made to measure;
-Unlimited design possibilities, single, double, with side or upper panels; inswing or outswing;
-Designed for the premises with high risk of burglary both private and public; indoor and outdoor use (when using finishing made to withstand outdoor conditions).
Certificates
Standard door set
More about the features of the door
Technical data
Note. All the parameters indicated in this table are valid for the doors with internal and external architraves.
1. Door frame – bent L-shaped profile of 100 mm, fixed in the door aperture by 16 pins, protected from cutting by steel sleeves of 24 mm. Complete thermal insulation by rock wool or foam.
2. Door leaf – special bent metal construction with 100% thermal insulation by 50 mm rock wool. Total width of the leaf is 75 mm. With protective boxes of the locks.
3. Reinforced, adjustable hinges with supporting bearings, covered with chrome-plated finishing caps – 2 pieces.
4. Protective pins for door hinges (16 mm Ø) – 4 pieces.
5. Insulation seals – 2 pieces.
6. Peephole.
7. Outside and inside door leaf finish – painted EDM board or WRB.
8. Outside architraves.
9. Inside architraves (if the door has to be fire-resistant).
10. Locks – optional, but one of the locks has to be no lower than 5th security class, see here.
11. One of the locks is protected by drilling resistant plate.
12. The lock rods of three directions are additionally protected by steel tubes.
Secure
Specially bent L-shaped 100 mm wide door frame is not only wider than that of ordinary armoured door, but also has 6 bending edges and thus is stronger than rectangular frames, which have only 4 bending edges. Moreover, the frame is fixed in the aperture by 16 plugs, which are protected from cutting by steel liners of 24 mm, thus there is no need to fix the door in concrete. Internal leaf construction is reinforced by rigid edges that do not allow deforming the door easily during burglary. One of the locks installed in this door model must be no lower than 7thsecurity class and protected by a drilling resistant manganese plate. Both locks are installed in protective steel boxes, and a separate protective sleeve secures each pin in the frame.
SKYDAS STANDART 3 RC4 hinges are reinforced and adjustable. On the hinges side there are 4 protective pins (16 mm Ø) that do not allow dislodging the door leaf if the hinges are cut.
The locks can be replaced without disassembling the door, so it is easy and fast.
Saves the heat in your home
As the bent profile leaf structure does not have closed cavities, it can be completely thermally insulated by 50 mm rock wool. The L-shaped bent frame and threshold ensure exclusive tightness as an additional seal is applied to the entire perimeter (two seals in total).
Thermal transmittance of SKYDAS STANDART 3 RC4 is 1.3 W/(m2K), i.e. the same like of 6-chamber plastic windows (the lower the transmittance, the more heat is held in). Therefore, this door is suitable not only for an apartment, but also for a private house (using the materials suitable for outdoor conditions).
Tight, good heat and sound insulation
Due to the above mentioned full thermal insulation of the door construction, the sound insulation of the door SKYDAS STANDART 3 is 41 dB. This door is especially tight and therefore, perfectly shuts out the odours and smoke from the outside.
Fire resistant
With additional fire resistant components SKYDAS STANDART 3 RC4 can protect from fire for as long as 45 minutes and withstand the temperature of 1000ºC. The certificate was issued by Inspecta Estonia OU, No. 1527-CPD-0017. The boiler room doors of private houses already have to meet fire protection requirements. The fire can also spread from the garage.
Durable and lasting, convenient to use
All SKYDAS doors are manufactured by especially precise programmed machines Amada, which can process metal with the precision of 0.1 mm, therefore, their construction is precisely accurate and straight. As hinges with supporting bearings are used, the doors are easy to open and close, despite of heavier weight characteristic to metal doors. The tests indicated that after 200,000 cycles of opening and closing, the construction of the door remained completely intact.
As the internal construction of the door has no closed cavities, the entire metal construction is covered in powder coating, which ensures long-term surface protection from corrosion.
There are several options for the door finishing. Most commonly we use sustainably sourced EDM board (Extreme Durable MDF). It gives the freedom of design and is also water resistant, dimensionally stable and withstands severe atmospheric changes therefore is ideal for the finishing of entrance doors. For those who prefer wood-looking entrance door we offer – Water Resistant Board (WRB) made of natural hardwood veneers (okoume). This type of plywood is designed to withstand the most severe outside conditions. It‘s wood texture gives the luxury look to your door and does not limit your design ideas.
Under necessity, door finish can be easily replaced.
It is recommended to use galvanized steel RUUKKI for entrance door construction.
Simple to take care of
Painted door finish does not require any specific care and is easy to clean with non-abrasive cleaners.
Design possibilities
Choose a design from nearly 200 our finish carvings or we will manufacture a door according to an individual project prepared by an architect or us.
See GALLERY for door photos.
If you need warmer door designed specially for outdoors conditions, choose SKYDAS 2000.
However, if higher security level is necessary, choose security doors SKYDAS PREMIUM PLIUS, which burglar resistance was tested and certified in an authoritative notified scientific research laboratory IFT Rosenheim, Germany. These doors were created applying the knowledge of the above mentioned laboratory of all possible ways and methods of burglary.
The door is manufactured precisely according to necessary measurements.
Important:
Burglar resistance certificate is applicable to door measurements 2100×980 mm, outwards opening door. The height and width of the door can be increased by 10% or reduced by 20%.
Fire resistance EI45 of the fire resistant door is applicable to measurements up to 2100x 980 mm. If the height or width is increased by 15% (but not more than 20% of the total area), fire resistance will be EI30.
Threshold
Available thresholds (2 mm thick):
- black metal,
- RUUKKI galvanized steel,
- matt stainless steel
Item photo | Description |
Handle ASSA 6638, with spring. Finishing: Chrome Mat chrome Other- on request |
|
Handle ASSA 1956, with spring Finishing: Chrome Mat chrome Other- on request |
|
Handle ASSA 6647 Finishing: Chrome Mat chrome Other- on request |
|
Fixed handle ASSA 496 Finishing: Chrome Mat chrome Other- on request |
|
Handle Y96, with spring Finishing: Chrome Mat chrome |
|
Handle ASSA YALE A6647, with spring. Finishing: Chrome Mat chrome |
Handle K27, with spring
Finishing:
Chrome
Mat chromeMat stainless steel handle up to 1m. (stainless steel decoration of the door leaf is not included)Mat stainless steel handle up to 2m.Cable shell (for electromechanical locks)ASSA case plateMottura drill resistive lock plate (to protect the lock from drilling). Suitable for locks: Mottura, Fiam and Mul-T-Lock CFMA.Stainless steel decoration up to 0,3m2 of the door leaf (handle is not included)Stainless steel decoration up to 0,3m2 at the bottom of the door leaf.3D milling up to 0,3m2Ventilation gridDoor closer ASSA D15
(for the door up to 85 kg) Door closer ASSA D35
(for the door up to 120 kg) Extra prolonged rings into case (for safe type lock for the doors Skydas 2000) Glossy brass plastic hinge covers Glossy chrome plastic hinge covers Mat stainless steel hinge covers Electric bolt Down sliding door seal
The peak to protect from rain (for the interior-opening doors)
Sloping threshold 15x100x20 mm
Door leaf laminated with 2 PVC colours up to 0,2m23-pins additional locking mechanism MOTTURA 96087IAlarm sensor at the top of the casing
Without inner opening decoration
With inner opening decoration
|
Interior opening decoration |
Other accessories:
All metal construction made of electro-galvanized steel RUUKKI (for the door to be used in the outdoor conditions).
All metal construction made of mat stainless steel.
All metal construction made of glossy stainless steel.
Glazing of various shapes.
Metal door construction is given the warranty of 5 years.
The colour coating of the metal door construction for using under interior conditions is given the warranty of 3 years.
The colour coating of the galvanized metal door construction for using under outdoor conditions is given the warranty of 2 years.
Door finish:
- MDF board, laminated by PVC film (interior conditions) – 3 years.
- Umidax HLS board, painted (outside and inside) – 1 year.
- Umidax HLS board, laminated by PVC film (without milling) under outdoor conditions, for the outside of the door – 1 year.
- Umidax HLS board, laminated by PVC film (without milling) under outdoor conditions, for the inside of the door – 1 year.
- Solid wood and natural veneer are available on request. Under interior conditios warranty 3 years. Under outside conditions – not given the warranty.
Locks – manufacturer’s guarantee (see LOCKS).
Peepholes, handles, seals, lock finish parts are not given a warranty.